|
|
Machine, Tools & Components
|
Suppliers Directory
|
GEM COOLING TOWERS (P) LTD
Manufacturer Of Coling Tower, Spriklers And Fans Only.
| | Address : |
SF NO: 100/A, ARASUR PO AVANASHI ROAD, |
| Telephone : |
0422-888513, 880130 |
| Fax : |
91-422-888523 |
| Send : |
On-Line Trade Inquiry |
| |
|
Products |
|
DRY COOLING TOWERS - DRY COOLING TOWERS, CAN BE USED FOR ANY APPLICATION WHERE PROCESS HOT WATER IS COOLED TO TEMPERATURE SLIGHTLY, ABOVE THE AMBIENT TEMPERATURE. THIS COOLING TOWERS IS MAINLY USED FOR GENERATOR SET AND AIR COMPRESSOR SYSTEM. TOWERS ARE USED IN OIL REFINERIES, SUGAR MILLS, FURNACE COOLING, INJECTION MOULDING MACHINES AND RUBBER AND TYPE INDUSTRY.
|
|
REFRIGERANT COMPRESSED AIR DRIERS - GEM EQUIPMENTS PRESENTS REFRIGERANT COMPRESSED AIR DRIER, MODEL: 2KD SERIES. THIS SERIES IS DESIGNED TO MAINTAIN 100% SEPARATION EFFICIENCY FROM LOW FLOWS TO FLOWS WELL ABOVE RATED CAPACITY. THESE ARE DESIGNED FOR LOW ENERGY USAGE THAT HELPS IN MINIMISING POLLUTION. THE DESIGN MAXIMIZES EXCHANGER EFFECTIVENESS BY USING COPPER TUBES IN A COILED TUBE IN TUBE ARRANGEMENTS. EFFICIENT SEPARATION ENSURE THAT LIQUID LEAVING THE EVAPORATED IS NOT CARRIED OVER IN THE OUTLET AIR WHERE IT RE-EVAPORATES RAISING THE OUTLET DEW POINT. THE HIGHLY ACCURATE HOT GAS BY-PASS VALVE AUTOMATICALLY MAINTAINS REFRIGERATION TEMPERATURE ACROSS A WIDE RANGE OF FLOWS AND AMBIENT CONDITIONS. ELECTRICAL CONSTRUCTION IS IN ACCORDANCE WITH APPLICABLE CODES. UNIQUE CO-EX EXCHANGER PERFORMS AS A PRECOOLER AND EVAPORATOR. TECHNICAL SPECIFICATION: WORKING PRESSURE - 7 BAR/16.5 BAR (MAX); INLET TEMPERATURE - 40°C/50°C (MAX); AMBIENT TEMPERATURE - 40°C/50°C (MAX); AND PRESSURE DEW POINT - 3°C.
|
|
REGENERATIVE DESICCANT COMPRESSED AIR DRYERS - GEM EQUIPMENTS PRESENTS REGENERATIVE DESICCANT COMPRESSED AIR DRYERS. THESE DRYERS WITH TOWERS ARE MAINLY DESIGNED TO PRESERVE THE HEAT OF ABSORPTION RELEASED DURING THE DRYING CYCLE. THE AIR ENTERS THE BOTTOM OF THE TOWER AND FLOWS UPWARD. UP FLOW DRYING PERMITS THE LIQUID IN THE INLET AIR TO SETTLE OUT ON THE BOTTOM OF THE TOWER. AS THE AIR FLOWS THROUGH THE TOWER IT IS IN CONTACT WITH THE DESICCANT FOR SUFFICIENT TIME TO PRODUCE THE DESIGN DEW POINT. ABOUT 98% OF THE HEAT OF ABSORPTION AND A MINIMUM AMOUNT OF PURGE AIR IS NEEDED FOR REGENERATION. THIS PREVENTS THE BED FROM FLOATING (FLUIDIZING) AND THE DESICCANT FROM DEGRADING (DUSTING). THE CHECK VALVE THROTTLES A PORTION OF THE DRY AIR BY MEANS OF AN ORIFICE, WHICH REACTIVATES THE DESICCANT IN TOWER II. THE CYCLE IS CONTINUED AT A PRE-SET TIME. HIGHLY ACCURATE ELECTRONIC TIMER OFFERS HIGHER PRESSURE AND LOWER DEW POINTS.ITS FEATURES: A FRONT MOUNTED CONTROL PANEL WITH POWER ON LIGHT, ON-OFF SWITCH AND TOWER PRESSURE GAUGES SUPPLIED WITH PRE AND AFTER FILTER, AMPLY SIZED NON CORROSIVE ALUMINIUM TOWERS; HEAVY-DUTY PURGE EXHAUST MUFFLER FOR NOISELESS OPERATION; NON-LUBRICATED SOFT SEATED CONTROL VALVES; STAINLESS STEEL SUPPORT SCREENS AND AIR DIFFUSERS; FURNISHED IN FOR EASY MOUNTING ARRANGEMENT; AND DRYER IS COMPLETELY ASSEMBLED, PIPED AND WIRED AT FACTORY.
|
|
COOLING TOWERS - GEM COOLING TOWERS PRESENTS COOLING TOWERS HIGHLY EFFICIENT AND LOW ENERGY CONSUMING DIRECT DRIVEN FAN, MODEL CFT SERIES.AN AXIAL FAN MOUNTED ON SS304 SHAFT SPECIAL CONSTRUCTION IN THE HORIZONTAL DIRECTION SUCKS THE AIR. THE GLASS FIBRE REINFORCED POLYESTER FAN HOOD ENSURES SMOOTH FLOW OF AIR CONSUMING MINIMUM POSSIBLE ENERGY. THE AIR IS IN DIRECT CONTACT WITH WATER ENABLING EASY EVAPORATION AND BETTER HEAT TRANSFER. THE COLD WATER IS COLLECTED IN THE FRP BASIN AT THE BOTTOM OF THE TOWER FOR RE-CIRCULATION. TECHNICAL SPECIFICATION, MODEL CFT-010: INLET - 1-1/2"; OUTLET - 1-1/2"; FLOAT - 1/2"; DRAIN - 1"; SHIPPING WT - 75 KG; OPERATION WT - 200 KG; AND MOTOR - 0.25 HP. SPECIAL FEATURES - HIGH EFFICIENCY; LOW ENERGY CONSUMPTION; ANTI-CORROSION AND LONG LIFE; USES UV STABILIZED RESIN; LOW MAINTENANCE; AND GRAVITY WATER DISTRIBUTION SAVES PUMP ENERGY.
|
| |
|
View More Supplier Pages
Page(s) : 1 •
2 •
3 •
4 •
5 •
| |
|
|
| Free Product Alert |
Receive regular
FREE alert
on new product
launches of Industrial Process Equipments & Accessories
|
| | | |
|
